[. . . ] TM
Hitachi UltraVision® HDTV Monitor
1. 5TM UltraThin LCD HDTV Monitor 32" Class (31. 51" Diagonal) Anthracite Pearl Crystal Frame(UT32V502) White Pearl Metallic Crystal Frame(UT32V502W) 1366 x 768p 120 Hz, PictureMasterTM V (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio
Operating Guide
UT32V502 UT32V502W
Model Name
Record the serial number of your monitor for future reference. SERIAL NO.
This serial number is located on the back and right side of the monitor. If you have a question about this product please call 800-Hitachi for assistance
READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE.
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect your Equipment to the Monitor (continued)
Connecting to a PC
The PC connection terminal (D-sub 15 pin) + the PC (RGB)/DVI Analog Audio Input terminal are connected to the PC, allowing an analog RGB signal.
IN
AUDIO
OUT
[Example]
(Audio)
or
(D-sub 15 Pin)
NOTE
About the connection of D-sub 15 pin, see
13
for details.
3. Attach Cushion, Secure with Clamps and Fit Terminal Cover
1
Attach the supplied cushion around the HDMI cable.
Cushion (supplied accessory) HDMI cable
Attach the cushion around the HDMI cable so as not to leave any clearance.
2
Unfasten 2 clamps, and then connect the HDMI cable and power cord to the monitor through open clamps.
Clamp Power cord
HDMI cable
CONNECTION (continued) 3. Attach Cushion, Secure with Clamps and Fit Terminal Cover (continued)
3
Secure the HDMI cable and power cord with clamps.
Clamp
4
Fit the terminal cover onto the monitor.
Insert the tabs into the slots as shown and fold downward to fit the terminal cover.
How to remove the cover.
Tabs
Terminal Cover
Using your fingers, pull backwards to lift the cover.
4. Connect the Power Plug into the Wall Socket
Connect the power cord after completing all other connections. (For some countries the type of plug is different that depicted. )
Monitor Rear Panel AC Wall Socket
CAUTION
Use only the power cord provided. Do not use a power supply voltage other than that indicated (AC120, 60Hz). For the LCD monitor, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pin grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line. If you have to change the power cord, please use a certified power cord that meets your region's safety standards. 21
BASIC OPERATION
ENGLISH
22
Power On/Off
Turn On the power of the unit. Illumination Lamp Indicating Lamp
To turn On the power to the unit:
1. The Indicating Lamp illuminates in Green, and the Illumination Lamp turns Blue. Once the Main Power switch is on, you can turn On/Off by pressing the Power (On/Off) button on the remote control.
Main Power Switch (on the underside) Front
To turn Off the power to the unit:
1. The Indicating Lamp turns Red (Standby mode), and the Illumination Lamp turns off. Press the Main Power switch on the unit to completely turn Off the power to the unit.
NOTE
Rear
Power On/Off button
While the Indicating Lamp illuminates in Red (Standby mode), you can turn On/Off by pressing the Power (On/Off) button on the remote control.
The Indicating Lamp/Illumination Lamp Status
Indicating Lamp Off Red Green Orange Blinking Green
NOTE
Illumination Lamp Blue Blue
Power Status Off Standby mode On Power Save mode On Refer to
42
Remark and
43
for the condition.
Receiving Remote Control signal
If the image does not appear on the screen at all, or if there is any problem with it, see "TROUBLESHOOTING" on 43 ~ 45 . After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control and the unit (such as the Power button) do not work during this period of time. If power is interrupted during use of the unit, to avoid sudden surges of electricity when the power comes back on, turn off the main power to the unit before leaving home.
BASIC OPERATION (continued) Volume Up/Down
1. To increase the sound volume, press the Volume Up button on the remote control or control panel. To decrease the sound volume, press the Volume Down button on the remote control or control panel. The color of the Volume Indicator will turn into grey while muting the volume. [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]